The Perkin-Elmer 4400 Series is a fast cycle, water-cooled load locked system that uses circular or delta style cathodes. It has the advantage of eliminating the need to vent the process chamber for loading and unloading substrates, reducing pump down time, contamination, and target burn-in. This increases material utilization. The system is a general-purpose sputtering system with up to four 8 inch diameter circular cathodes that can use DC Magnetron, RF Magnetron, or RF Diode configurations. These can be sputtered sequentially without breaking vacuum. Power sources are available up to 2 kW RF and 5 kW DC.

PERKIN ELMER

4400

The ELAN DRC II combines the power of patented Dynamic Reaction Cell (DRC) technology, performance-enhancing Axial Field Technology (AFT) and a high-performance sample introduction system with the ability to run any reaction gas. The result is the ultimate analytical tool, providing uncompromised sensitivity and performance in all matrices for the world’s most difficult applications. Unlike collisioncell, high-resolution or cool-plasma systems, the ELAN DRC II completely eliminates polyatomic interferences, minimizing background equivalent concentrations, while maintaining analyte sensitivity, providing ultratrace-level detection limits in virtually any sample.

ELAN DRC II

The Perkin-Elmer 4450 is a type of sputtering system that belongs to the Perkin-Elmer 4400 Series. It is similar to the Model 4410, but has additional features such as load lock pumping and substrate heating. The system can operate automatically and has three Delta™ cathode positions, one of which can be replaced with an in-process heater fixture. The Perkin-Elmer 4450 Sputter Deposition System is designed to be flexible and offers a variety of operating and process modes. 

4450

2400

SPECTRUM 100

Optima 8300

SPECTRUM ONE

The PerkinElmer Frontier™ range of near-,mid- and far-IR Fourier Transform spectrometers

FRONTIER 

Perkin–Elmer Physical Electronics Model 6300 secondary ion mass spectrometer (SIMS)

6300 SIMS

OPTIMA 7300DV

LAMBDA 850

Optima 4300 DV

NexION 350

LAMBDA 20

2400-8L

LAMBDA 9

The Perkin-Elmer Model 2400-8SA features a large 211/2” rotating, water cooled annular table with a capacity of sixty-four 2″, thirty 3″, or thirteen 4″ wafers.

Used in conjunction with a cathode shaping aperture, the rotating table permits high uniformity. A 4″ wafer vertical range of the table facilitates coating bulk substrates. As an added feature, up to three 8″ round cathodes may be specified allowing sequential deposition from several targets or alternately, static deposition or heating from any target position.



2400-8SA

SPECTRUM 1000

The QSight LC/MS/MS System provides the capability and confidence required to analyze the most complex food and environmental samples. With high level of sensitivity and throughput, laboratories can meet even the most stringent regulatory requirements rapidly, easily, and effectively

Sensitivity for the most demanding regulations
Easy-to-use with ready to implement methods
Patented flow-based technology that enables up to 15% more productivity
StayClean™ Source, self-cleaning design for maximum sensitivity and exceptional uptime
Laminar Flow Ion Guide™ for highly efficient field-free transmission, providing virtually no maintenance requirements
Dual Source technology gives you the capability to set ESI or APCI modes, with two independent probes for true multiplexing
Modular Simplicity™ 3Q Software to acquire, quantify, and report with flexible data viewing options and powerful remote diagnostics.
Different models available (QSight 110 LC/MS/MS, QSight 210 LC/MS/MS, QSight 220 LC/MS/MS, QSight 420 LC/MS/MS) addressing different levels of performance and efficiency required by different labs’ analysis needs.


QSight 420 LC/MS/MS

SIMAA 6000

NexION 2000

NexION 300D

NexION 300x

NexION 350X ICP-MS lets you minimize analysis times without compromising your desired level of interference removal or detection limits. The instrument’s Universal Cell Technology also enhances laboratory productivity. Dual-channel Universal Cell (2 gas lines) 

NexION 350X

Differential Scanning Calorimeter (DSC) measures the amount of energy (heat) absorbed or released by a sample as it is heated, cooled or held at a constant (isothermal) temperature. The precise measure of sample temperature is also made with a DSC. It is used for the calorimetric measurement, characterization, and analysis of thermal properties of materials. Types of thermal analysis measurement typically performed by DSC would be as follow: Melting, Crystallization, Glass Transition, Polymorphism, Purity, Specific Heat, Kinetic Study and Curing Reaction. The Diamond DSC is designed using the unique power compensation approach, which yields true heat flow measurements. Because of the very low mass (<1g) and independent furnace design of the power compensation approach, the Pyris Diamond DSC provides both the necessary very high sensitivity and unsurpassed resolution necessary for the measurement of polymorphism exhibited by pharmaceuticals.

Diamond DSC

430P

The Perkin-Elmer LAMBDA 950 is a high-performance spectrophotometer that has long been considered the industry standard. It uses a gridless PMT with a Peltier-controlled PbS detector to achieve high-performance testing across the spectral range up to 3300 nm. The UV/Vis resolution of the LAMBDA 950 reaches 0.05 nm, while the NIR resolution reaches up to 0.20 nm. The LAMBDA 950 also features industry-leading components and accessories for sample control and flexibility, including large, dual sample compartments, a Universal Reflectance Accessory, snap-in integrating spheres, and a General-Purpose Optical Bench.

LAMBDA 950

PLASMA 40

Optima 3000 

The DRC-e brings the interference eliminating power of patented Dynamic Reaction Cell™ (DRC™) technology and performance-enhancing Axial Field™ Technology (AFT) to the industry-proven ELAN ICP-MS system. The result is uncompromised sensitivity and performance in a robust system designed for routine laboratories. The ELAN DRC-e uses chemical resolution to eliminate plasma-based polyatomic species before they reach the quadrupole mass spectrometer. This ion-molecule chemistry uses a reaction gas to “chemically scrub” polyatomic or isobaric species from the ion beam before they enter the analyzer, resulting in improved detection limits for traditionally difficult elements, including As, Cr, Fe, Se and others. And, unlike collision-cell, high-resolution or cool-plasma systems, the ELAN DRC-e system eliminates not only the primary interference; but also prevents the formation of new interferences, while maintaining analyte sensitivity – providing ultratrace level detection limits in virtually any matrix. 

ELAN DRC-e

NexION 350D

AAnalyst 400

OPTIMA 2100 DV

AAnalyst 800

LAMBDA 40

LAMBDA 2

Time of flight mass spectrometer (TOF MS)

AxION 2 

LS-55

FLEXAR SQ 300

The PerkinElmer Diamond Thermogravimetric/Differential Thermal Analysis (TG/DTA) system combines the flexibility of DTA with the proven capabilities of the TG measurement technology, providing property information for a variety of samples in the temperature range from ambient to 1500C. The simultaneous TG/DTA system can be used for such applications as oxidation, heat resistance, the amount of water, compositional analysis and the measurement of ash content in a sample. This system is also used to cover such needs as reaction rate and accelerated degrading tests.

Diamond TG/DTA

The LAMBDA 750 is designed to provide the maximum sampling flexibility for tough samples in chemistry,
biochemistry and materials science. The system is ideal for a busy research or teaching laboratory, as accessories and detector modules can quickly and easily be interchanged to provide the optimum configuration for each measurement. For industrial applications, the design of the LAMBDA 750 and its accessories maximizes productivity through simple design which minimizes adjustment and maintains critical performance at the highest level.

LAMBDA 750

AAnalyst 200

TGA 7

4410

Optima 7000 DV

INTRACOOLER 2P

8800

4480

ELAN 6100 DRC

The Clarus 590 and 690 systems' all-new wide-range flame ionization detector (FID) measures hydrocarbon compounds at very low and very high levels, with a linear response range of 107. That allows you to accurately quantitate the largest and smallest peaks on a chromatogram without changes to range or attenuation. 

Clarus 690

The NexION® 1000 ICP-MS is a cost-effective, high-throughput mass spectrometer designed for routine, multi-elemental trace-level analysis compliant with regulatory standards. It incorporates unique technologies to offer remarkable speed and ease of operation, significantly enhancing laboratory efficiency.

NexION 1000

The Avio® 550 Max is a high-efficiency, compact ICP-OES instrument designed for laboratories with demanding throughput needs. Featuring a vertical plasma, it excels in analyzing high-matrix samples without the need for dilution, ensuring enhanced productivity and performance.

Avio 550 Max

2400 AL

The PerkinElmer Clarus® 600 Mass Spectrometer (MS) is a detector that is interfaced to the
Clarus 600 Gas Chromatograph (GC). The entire system is controlled through the PerkinElmer
TurboMass™ GC/MS software.
Electron ionization with 255 L/sec turbomolecular pump.

Clarus 600 T MS

The PerkinElme Clarus® 600 Mass Spectrometer (MS) is a detector that is interfaced to the
Clarus 600 Gas Chromatograph (GC). The entire system is controlled through the PerkinElmer
TurboMass™ GC/MS software.
Electron ionization with 75 L/sec turbomolecular pump.

Clarus 600 S MS

AAnalyst 700

TurboMatrix HS 40

PHI 40-700

With its new high performance features, our robust Clarus® 590 GC offers improved sensitivity, reduced carryover and is easy to use and maintain. Designed with the same innovative features of the Clarus 690 GC, you have the most versatile sample handling options to choose from. Our comprehensive, industry-leading TurboMatrix™ solutions include options for headspace (HS), manual and automated thermal desorption (TD, ATD) and a flexible MultiPrep Autosampler for liquid sampling and SPME.

Clarus 590 GC

Ideal for laboratories testing semiconductors and fine chemicals, the NexION 2000S ICP-Mass Spectrometer features:

- A dedicated SMARTintro™ High Purity sample-introduction module minimizes contamination and delivers low background equivalent concentrations (BECs)
- Built-in cold plasma capabilities which, combined with Reaction mode, deliver PPQ detection limits
- Three quadrupoles, three gas channels, and three modes of operation combine to offer better interference removal, delivering better detection limits/improved data accuracy
- The industry’s fastest data acquisition speed on the market (100,000 points/sec) to handle any particle size
- A new solid-state RF generator with revolutionary LumiCoil™ technology – first ICP-MS RF coil that requires no maintenance or cooling
- Triple Cone Interface with Quadrupole Ion Deflector, delivering no maintenance beyond the cones
- Small footprint to minimize bench space
- Syngistix™ software provides an intuitive interface that mirrors your workflow, with left-to-right, icon-based navigation that guides you through your analysis. 

Plus, it’s a cross-platform solution, easing the transition from technique to technique.

NexION 2000S

The PerkinElmer Optima™ 8000 ICP-OES instrument is used to determine the concentration of Ca, Mg, Fe, Al, Ni, Ba, Mn, Sr and Pb in purified brines in the Chlor-alkali industry.

Optima 8000

2400-SSA

AutoIMAGE FT-IR

The TGA 4000 Thermogravimetric Analyzer is designed with a compact ceramic furnace, which provides the temperature control you need for accurate results. Its rugged design is also corrosion resistant for the applications flexibility you need today and tomorrow.

TGA 4000

RANDEX 3400

TR 2900

Lambda 25

LAMBDA 1050

Clarus 680 GC

DMA 8000

8880

The PerkinElmer Clarus® 600 Mass Spectrometer (MS) is a detector that is interfaced to the
Clarus 600 Gas Chromatograph (GC). The entire system is controlled through the PerkinElmer
TurboMass™ GC/MS software.
Electron ionization (EI) and chemical ionization (CI) with 255 L/sec turbomolecular pump

Clarus 600 C MS 

TL-9000

OPTIMA 2000 DV

The PerkinElmer TMA 4000 is a uniquely designed thermomechanical analyzer (TMA) designed for optimal performance in measuring the coefficient of thermal expansion (CTE) in materials.

TMA 4000

3110

The DSC 4000 is a reliable, single-furnace heat flux Differential Scanning Calorimeter (DSC) designed for routine applications. It features an easy-to-load vertical furnace, notable for its resistance to oxygen and chemical corrosion, ensuring consistent performance and quality results.

DSC 4000

4410 DC

The PerkinElmer Avio® 200 is a compact, hybrid-scanning ICP system designed for efficient handling of high-matrix samples without dilution. It combines superior performance with ease-of-use, featuring unique hardware and intuitive software for both multi-element and single-element analyses. Key highlights include the lowest argon consumption among ICPs, the fastest startup time, exceptional sensitivity and resolution for various elements, and an extended linear range through dual viewing technology. This system offers reliable data and cost-effective operation, making it an ideal choice for diverse ICP-OES applications.

Avio 200

Clarus 500

AAnalyst 600

OPTIMA 7100 DV

ELAN 9000 DRC

OPTIMA 5300 DV

4410B

ELAN 9000

Lambda 3B

Spectrum Two is the FT-IR spectrometer of choice for everyone, everywhere. With fully integrated, robust universal sampling for trouble-free measurements and portability options, Spectrum Two is ideal for use in both laboratory and remote testing environments. Ideally suited to everyday analysis, you can confidently perform fast, accurate IR analysis and assure the quality of your materials across a wide range of applications.

SPECTRUM TWO

DSC 8000

The PerkinElmer Clarus® 600 Mass Spectrometer (MS) is a detector that is interfaced to the
Clarus 600 Gas Chromatograph (GC). The entire system is controlled through the PerkinElmer
TurboMass™ GC/MS software.
Electron ionization with air-cooled oil diffusion pump.

Clarus 600 D MS 

ELAN DTC II ICP

The PinAAcle 500 is a robust, fully-integrated, flame-only benchtop system, ideal for laboratories needing a reliable, easy-to-use, yet high-performance flame AA. It is equipped with an innovative touchscreen interface with the flexibility to operate via its easy-to-use Syngistix Touch™ software or the more comprehensive, optional Syngistix™ for AA Software.

The PinAAcle 500 is designed for:
Exceptional sensitivity and precision, allowing analysis of lower concentrations with the accuracy of higher-end AA systems
Fast, simple, reproducible operation through the intuitive, icon-based interface of Syngistix Touch or Syngistix for AA
Harsh environments and samples thanks to its corrosion-resistant sample introduction components
Minimum maintenance and maximum speed with a rugged design that virtually eliminates maintenance, reducing operating costs

PinAAcle 500

PerkinElmer's Avio® 220 Max ICP-OES gains its outstanding analytical performance from its novel optical system, including a unique double monochromator, dual backside-illuminated charge-coupled device (DBI-CCD) detector, real-time dynamic wavelength stabilization for plug and play (cold start to sample analysis in 10 minutes), in line attenuation by wavelength, and automatic dual viewing of the plasma torch. It’s the combination of these innovative components that provides the Avio 220 Max ICP-OES with: 
• Excellent spectral resolution 
• High analytical flexibility 
• Lowest argon consumption 
• Expanded linear dynamic range 
• Reduced spectral interferences 
• Maximum light throughput 
• Exceptional analytical speed

Avio 220 Max

1760-X


The Avio® 500 is a compact ICP-OES featuring simultaneous, dual view capabilities and a vertical plasma design. It excels in processing high-matrix samples without dilution, ensuring high productivity and performance. Key benefits include exceptional matrix tolerance, minimal argon consumption (at least 50% less than other systems), simultaneous background correction for quick and accurate data, and high throughput due to its dual view technology. 

PERKIN ELMER

概述

活动的上架物品

总产品

服务

热门产品

4400

ELAN DRC II

4450

2400

使用 Moov 上架，立即找到完美买家。

所有产品

查看所有上架物品