说明
无说明配置
Frequency Range: 0.7–4.2GHz instantaneously RF Connector: RF Connector Type N female REMOTE INTERFACES: IEEE-488-24 pin female RS-232-9 pin Subminiature D (female) RS-232 (fiber optic)-Type ST USB 2.0-Type B Ethernet-RJ-45 Standards Met: CE Mark Testing Gain: (at maximum setting) 43 dB minimum (Continuous Range) 10 dB minimum RF Input Voltage: 1.0 milliwatt maximum for rated output Impedance: 50 ohms, VSWR 2.0:1 maximum Input: 90-132, 180-264 VAC 50/60 Hz, single phase 210 watts maximum Output: POWER OUTPUT @ 3dB COMPRESSION Nominal 25 watts Minimum 20 watts POWER OUTPUT @ 1dB COMPRESSION Nominal 22 watts Minimum 18 watts Flatness: ± 1.5 dB Harmonic Distortion: (THD) Minus 20 dBc maximum at 15 watts Dimensions: 19.8 x 6.1 x 14.8 in Weight: 37 lbsOEM 型号描述
The Model 20S1G4 is a solid state, self-contained, air-cooled, broadband amplifier designed for applications where instantaneous bandwidth and high gain are required. Housed in a stylish contemporary cabinet, the unit is designed for benchtop use, but can be removed from the cabinet for immediate equipment rack mounting. The 20S1G4, when used with a sweep generator, will provide a minimum of 20 watts of RF power. Included is a front panel gain control which permits the operator to conveniently set the desired output level. The 20S1G4 is protected from RF input overdrive by an RF input leveling circuit which controls the RF input level to the RF amplifier first stage when the RF input level is increased above 0 dBm. The RF amplifier stages are protected from over-temperature by removing the DC voltage to them if an over temperature condition occurs due to cooling blockage or fan failure. There is a digital display on the front panel to indicate the operate status and fault conditions when an over-temperature or power supply fault has occurred. The unit can be returned to operate when the condition has been cleared. The 20S1G4 includes digital control for both local and remote control of the amplifier. All amplifier control functions and status indications are available remotely in GPIB/IEEE488 format, RS-232 hardwire and fiber optic, USB, and Ethernet. The bus interface connector is located on the back panel and positive control of local or remote operation is assured by a Local/Remote switch on the front panel of the amplifier.文件
无文件
AMPLIFIER RESEARCH
20S1G4
已验证
类别
Electronic Test
上次验证： 60 多天前
物品主要详细信息
状况：
Used
运行状况:
未知
产品编号：
60850
晶圆尺寸：
未知
年份：
未知
Have Additional Questions?
Logistics Support
Available
Money Back Guarantee
Available
Transaction Insured by Moov
Available
Refurbishment Services
Available
AMPLIFIER RESEARCH
20S1G4
类别
Electronic Test
上次验证： 60 多天前
物品主要详细信息
状况：
Used
运行状况:
未知
产品编号：
60850
晶圆尺寸：
未知
年份：
未知
Have Additional Questions?
Logistics Support
Available
Money Back Guarantee
Available
Transaction Insured by Moov
Available
Refurbishment Services
Available
说明
无说明配置
Frequency Range: 0.7–4.2GHz instantaneously RF Connector: RF Connector Type N female REMOTE INTERFACES: IEEE-488-24 pin female RS-232-9 pin Subminiature D (female) RS-232 (fiber optic)-Type ST USB 2.0-Type B Ethernet-RJ-45 Standards Met: CE Mark Testing Gain: (at maximum setting) 43 dB minimum (Continuous Range) 10 dB minimum RF Input Voltage: 1.0 milliwatt maximum for rated output Impedance: 50 ohms, VSWR 2.0:1 maximum Input: 90-132, 180-264 VAC 50/60 Hz, single phase 210 watts maximum Output: POWER OUTPUT @ 3dB COMPRESSION Nominal 25 watts Minimum 20 watts POWER OUTPUT @ 1dB COMPRESSION Nominal 22 watts Minimum 18 watts Flatness: ± 1.5 dB Harmonic Distortion: (THD) Minus 20 dBc maximum at 15 watts Dimensions: 19.8 x 6.1 x 14.8 in Weight: 37 lbsOEM 型号描述
The Model 20S1G4 is a solid state, self-contained, air-cooled, broadband amplifier designed for applications where instantaneous bandwidth and high gain are required. Housed in a stylish contemporary cabinet, the unit is designed for benchtop use, but can be removed from the cabinet for immediate equipment rack mounting. The 20S1G4, when used with a sweep generator, will provide a minimum of 20 watts of RF power. Included is a front panel gain control which permits the operator to conveniently set the desired output level. The 20S1G4 is protected from RF input overdrive by an RF input leveling circuit which controls the RF input level to the RF amplifier first stage when the RF input level is increased above 0 dBm. The RF amplifier stages are protected from over-temperature by removing the DC voltage to them if an over temperature condition occurs due to cooling blockage or fan failure. There is a digital display on the front panel to indicate the operate status and fault conditions when an over-temperature or power supply fault has occurred. The unit can be returned to operate when the condition has been cleared. The 20S1G4 includes digital control for both local and remote control of the amplifier. All amplifier control functions and status indications are available remotely in GPIB/IEEE488 format, RS-232 hardwire and fiber optic, USB, and Ethernet. The bus interface connector is located on the back panel and positive control of local or remote operation is assured by a Local/Remote switch on the front panel of the amplifier.文件
无文件